Pagong
06-25-2011, 09:39 AM
Haven't had a VIP car to work with for quite sometime now, here is my current one.
1980 Toyota Cressida with 1JZGTE-vvti swap
Its sitting on some SSR XR4 Longchamps
14x7 0 front
14x7.5 -5 rear
http://sphotos.ak.fbcdn.net/hphotos-ak-ash2/hs026.ash2/34659_414023793709_592353709_4632477_2521993_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-ash2/hs026.ash2/34659_414023798709_592353709_4632478_3027326_n.jpg
then we found out that the oil pump was dead...so out with the old:
http://sphotos.ak.fbcdn.net/hphotos-ak-ash2/hs143.ash2/40490_1517974466009_1133912780_1473638_6252357_n.j pg
http://sphotos.ak.fbcdn.net/hphotos-ak-ash2/hs155.ash2/41099_1518244512760_1133912780_1474257_6923206_n.j pg
and in with the new
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs277.snc4/40178_1521723319728_1133912780_1483565_3221974_n.j pg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs267.snc4/39669_1521723839741_1133912780_1483566_8010227_n.j pg
custom motor mounts using 1/4" flat stock steel
http://sphotos.ak.fbcdn.net/hphotos-ak-ash2/hs184.ash2/44746_1534763085714_1133912780_1519241_4555961_n.j pg
crossmember modified and ready to go
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs422.snc4/46483_1538980191139_1133912780_1532391_6148080_n.j pg
and the fun part.....wiring
from this
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs363.snc4/44648_1539007191814_1133912780_1532456_2054602_n.j pg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs397.snc4/45988_1539007351818_1133912780_1532457_1607685_n.j pg
and out of all those wires this is all that's left and needed
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs377.snc4/45977_1539007951833_1133912780_1532459_2737983_n.j pg
1980 Toyota Cressida with 1JZGTE-vvti swap
Its sitting on some SSR XR4 Longchamps
14x7 0 front
14x7.5 -5 rear
http://sphotos.ak.fbcdn.net/hphotos-ak-ash2/hs026.ash2/34659_414023793709_592353709_4632477_2521993_n.jpg
http://sphotos.ak.fbcdn.net/hphotos-ak-ash2/hs026.ash2/34659_414023798709_592353709_4632478_3027326_n.jpg
then we found out that the oil pump was dead...so out with the old:
http://sphotos.ak.fbcdn.net/hphotos-ak-ash2/hs143.ash2/40490_1517974466009_1133912780_1473638_6252357_n.j pg
http://sphotos.ak.fbcdn.net/hphotos-ak-ash2/hs155.ash2/41099_1518244512760_1133912780_1474257_6923206_n.j pg
and in with the new
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs277.snc4/40178_1521723319728_1133912780_1483565_3221974_n.j pg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs267.snc4/39669_1521723839741_1133912780_1483566_8010227_n.j pg
custom motor mounts using 1/4" flat stock steel
http://sphotos.ak.fbcdn.net/hphotos-ak-ash2/hs184.ash2/44746_1534763085714_1133912780_1519241_4555961_n.j pg
crossmember modified and ready to go
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs422.snc4/46483_1538980191139_1133912780_1532391_6148080_n.j pg
and the fun part.....wiring
from this
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs363.snc4/44648_1539007191814_1133912780_1532456_2054602_n.j pg
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs397.snc4/45988_1539007351818_1133912780_1532457_1607685_n.j pg
and out of all those wires this is all that's left and needed
http://sphotos.ak.fbcdn.net/hphotos-ak-snc4/hs377.snc4/45977_1539007951833_1133912780_1532459_2737983_n.j pg