y34 afm

[lowlyfey34]

IF anyone has an intake on their y34 (excluding you yudi) using the factory afm.....i'm curious if the z32 3.5" afm adapter is the same bolt pattern......if not, i might just buy one and hope it fits lol. but i got one from my g35 that imma see will bolt up.....

[lowlyfey34]

g35 maf adapter is too small. gotta try a z32 adapter now. lol

[Jer]

Z32 is super close looking. Im subscribing. Keep us updated.

°Jerimiah°

[kingpin]

http://i797.photobucket.com/albums/yy257/petrolheadvip/392324_10151085920880096_807045095_22658557_129907 495_n.jpg


http://i797.photobucket.com/albums/yy257/petrolheadvip/395538_10151085922915096_807045095_22658564_127620 6333_n.jpg


i am going to mass produce these for $550 each .. your check engine light will not come on!

Why stress you self you when you can just bolt it on .. :giggity:

or attempt to do this and stress you self out lol

it feels like a 10 hp gain .. i will do a DYno and let you guys know !

[marksport]

What I don't like about that kind of system is that the factory is quite good having a funnel in the front and that the aluminum piping conducts too much heat. These VK45 do run quite hot. If it was stainless or composite might be better but more expensive. I might have to go that route as my throttle body gets moved back a couple of inches.

[lowlyfey34]

....which is why i would like to keep the upper half all silicone tubing since it's in the engine bay....to prevent some heat soak. i need some measurements of the z32 afm before i go and spend $20-30 for an adapter lol but pre-afm pipe will be 3" then 3.5" after the afm since they afm housing measures roughly 3.5"

[Tony Two-Tone]

Subscribed.

[lowlyfey34]

ordered a z32 afm adapter. its an aluminum one with a 3.8" inlet. i plan on running a 3.5" intake like yudi but not as pretty and one-pieceish like yudi lol. i do plan on making the top half of the intake with all silicone....so no heak soaking bishesssss

[Dranom]

http://i797.photobucket.com/albums/yy257/petrolheadvip/392324_10151085920880096_807045095_22658557_129907 495_n.jpg


http://i797.photobucket.com/albums/yy257/petrolheadvip/395538_10151085922915096_807045095_22658564_127620 6333_n.jpg


i am going to mass produce these for $550 each .. your check engine light will not come on!

Why stress you self you when you can just bolt it on .. :giggity:

or attempt to do this and stress you self out lol

it feels like a 10 hp gain .. i will do a DYno and let you guys know !

if ever you sell one use that money to buy some engine degreaser and a brush=)

[lowlyfey34]

lol he got a free engine bay cleaning with the intake install

[kingpin]

lol .. its all spiffy clean now !!

that's that dirt .. it Oil from rust proofing ..BTW

[Kennyjevon]

subscribed

[Tony Two-Tone]

Did you have to cut the inner fender to get that in there? Mine is solid and doesn't go down in the wheel well


-Sideways the Seven

[lowlyfey34]

Yeah he cut a hole. What did you use for your afm?

[Tony Two-Tone]

Grabbed an aluminium MAF adapter and modded to match our bolt pattern and switched to a cone filter. Wanted to just mod the stock air box but it wouldnt have done much.

Now looking at a different idea with the piping.


-Sideways the Seven

[lowlyfey34]

yeah the z32 3.8" afm adapter i got, i had to slot the holes since the y34 afm has a bigger mounting flange, so i'll have to use a bolt/nut type deal....but i havnet put it on yet cuz i still need to get a 3.75" section of piping and a filter.

[Tony Two-Tone]

The filter is the easy part. I'm trying to figure out piping


-Sideways the Seven